Advances in applications of non-destructive testing (NDT): a review
Keywords:
acoustic emission, eddy current testing, manufacturing defects, non-destructive testing (NDT), ultrasonic testingAbstract
Manufacturing defects and discontinuities in a product are anomalies which can lead to severe damages which may sometimes involve loss of life. These defects must be examined and corrected before the product goes into service. There are two methods of testing a product for defects and discontinuities viz. Destructive Testing and Non-Destructive Testing. Destructive Testing entails subjecting the product to conditions that leads to failure of the product whereas Non-Destructive Testing (NDT) is the process of examining the products for defects in a way in which it retains its usefulness for future service. This paper discusses various methods involved in NDT such as Visual Testing, Magnetic Particle Inspection, Penetrant Testing, Ultrasonic Testing, Radiographic Testing, Acoustic Emission and Eddy Current Testing with a major focus on advances in the applications of NDT.
Downloads
References
A.D. Doulamis & T.A. Varvarigou (2011); Image analysis for artistic style identification: A powerful tool
Amenabar, I., Mendikute, A., López-Arraiza, A., Lizaranzu, M., & Aurrekoetxea, J. (2011). Comparison and analysis of non-destructive testing techniques suitable for delamination inspection in wind turbine blades. Composites Part B: Engineering, 42(5), 1298-1305. https://doi.org/10.1016/j.compositesb.2011.01.025
B. L. Luk and Alan, H. S. Chan (2007); Human Factors and Ergonomics in Dye Penetrant and Magnetic Particles Nondestructive Inspection Methods.
Binda, L., Saisi, A., Tiraboschi, C. (2000); Investigation procedures for the diagnosis of historic masonries, Construction and Building Materials, Elsevier, 14(4), 199–233.
Bruce W. Drinkwater, Paul D. Wilcox (2006); Ultrasonic arrays for non-destructive evaluation: A review, NDT & E International, 39(7), 525–541.
Construction and Building Materials, ISSN. 2003:0950-618
D. Bracun, I. Polajnar, J. Diaci (2006); Indentation shape parameters as indicators of spot weld quality; International Journal of Materials and Product Technology, 27(3/4), 247 – 257.
D.G. Aggelis, D.V. Soulioti, N.M. Barkoula, A.S. Paipetis & T.E. Matikas (2011); Influence of the fiber chemical coating on the fracture behavior of steel fiber concrete measured by acoustic emission, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 111-116.
da Silva, J., Jaidilson J, Lima, Marcus N.A., da Rocha Neto & Jose Sergio (2007b); Fouling detection using ultrasonic guided waves and parameter estimation, Third IFAC Symposium on System Structure and Control.
da Silva, J., Wanzeller, M.G., de Almeida Farias, P., da Rocha Neto & Jose Sergio. (2005); Development of Circuits for Excitation and Reception in Ultrasonic Transducers for Generation of Guided Waves in Hollow Cylinders for Fouling Detection, Instrumentation and Measurement Technology Conference, 467–471.
E. Cheilakou, N. Liarokapi & M. Koui (2011); NDT characterization of ancient glass objects from the Aegean with an approach of the manufacturing technique, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 63-70.
E. Tatsis, N. Zoidis, C. Vlachopoulos, T.E. Matikas & A. Gotzamanis (2011); Visual inspection and evaluation using NDT testing methods of industrial building after fire, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 131-136.
El Masri, Y., & Rakha, T. (2020). A scoping review of non-destructive testing (NDT) techniques in building performance diagnostic inspections. Construction and Building Materials, 265, 120542. https://doi.org/10.1016/j.conbuildmat.2020.120542
for preserving cultural heritage, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 71-76.
Francesca Cau, Alessandra Fanni Augusto Montisci, Pietro Testoni, Mariangela Usai (2006); A signal processing tool for non-destructive testing of inaccessible pipes; Engineering Applications of Artificial Intelligence, 19(7), 753–760.
G. S. Park, P. W. Jang, Y. W. Rho (2001); Optimum Design of a Non Destructive Testing System to Maximize Magnetic Flux Leakage; Journal of Magnetics, 6(1), 31-35.
Gabriel Dan Ta?c?, Gheorghe Amza; Research regarding ultrasonic examination of complex parts.
Gerd Dobmann, Iris Altpeter, Bernd Wolter (2008); Materials characterization a challenge in NDT for quality management; International Non-Destructive Testing Symposium and Exhibition, Istanbul Turkey.
Gholizadeh, S. (2016). A review of non-destructive testing methods of composite materials. Procedia Structural Integrity, 1, 50-57. https://doi.org/10.1016/j.prostr.2016.02.008
Giovanni M. Carlomagnoet, Carosena Meola (2002); Comparison between thermographic techniques for frescoes NDT, NDT & E International, 35(8), 559–565.
H. A. Crostack, W. Reimers ( 2001); Evaluation of component integrity by non-destructive testing; International Journal of Materials and Product Technology, 3(2), 147 - 162.
Hay, T.R & Rose, J.L. (2003); Fouling detection in the food industry using ultrasonic guided waves, Food-Control 14(7), 481–488.
Ignacio Garcia de Carellan, Phil Catton, Cem Selcuk & Tat-Hean Gan (2011); Methods for detection and cleaning of fouling in pipelines, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 231-236.
J. Skramlik, M. Novotny & K. Suhajda (2011); Apparatus for measuring of liquid conductivity, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 489-494.
J.S. Clausen, N. Zoidis & A. Knudsen (2011); Onsite measurements of concrete structures using Impact-Echo and Impulse Response, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 117-122.
Jacek Jarmulak, Eugene J.H. Kerckhoffs, Peter Paul van’t Veen (2001); Case-based reasoning for interpretation of data from non destructive testing; Engineering Applications of Artificial Intelligence; 14(4), 401–417.
Javier García-Martín, Jaime Gómez-Gil and Ernesto Vázquez-Sánchez (2011); Non-Destructive Techniques Based on Eddy Current Testing, Sensors, 11(3), 2525-2565.
Jolly, M. R., Prabhakar, A., Sturzu, B., Hollstein, K., Singh, R., Thomas, S., ... & Shaw, A. (2015). Review of non-destructive testing (NDT) techniques and their applicability to thick walled composites. Procedia CIRP, 38, 129-136. https://doi.org/10.1016/j.procir.2015.07.043
K. Bollas, D. Papasalouros, D. Kourousis & A. Anastasopoulos (2011); Acoustic emission monitoring of wheel sets on moving trains, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 341-346.
Li Zhijun (2001); Non-Destructive Testing of Advanced Composites; Aerospace Materials & Technology.
Lohr, K.R. & Rose, J.L. (2003); Ultrasonic guided wave and acoustic impact methods for pi1pe fouling detection, Journal-of-Food-Engineering 56(4), 315–324.
M. Ohtsu, T. Matsuo, S. Nozaki & Y. Kawasaki (2011); AE monitoring of shrinkage process in concrete, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 143-148.
M.D. Beard, M.J.S. Lowe (2003); Non-destructive testing of rock bolts using guided ultrasonic waves, International Journal of Rock Mechanics and Mining Sciences, 40(4), 527–536.
M.S. Kova?evi?, A. Mir?eta & D. Mar?i? (2011); NDT and safety of crude oil storage tanks, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 477-482.
Mc Clements, D.J. (1995); Advances in the application of ultrasound in food analysis and processing, Trends in Food Science and Technology, 6, 293–299.
N. Meyendorf, B. Frankenstein & L. Schubert (2011); Structural health monitoring for aircraft, ground transportation vehicles, wind turbines and pipes—prognosis, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 15-22.
N. Tsopelas, D. Kourousis, I. Ladis, A. Anastasopoulos, D.J. Lekou & F. Mouzakis (2011); Health monitoring of operating wind turbine blades with acoustic emission, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 347-352.
P Cawley (2001); Non-destructive testing—current capabilities and future directions; Journal of Materials: Design and Applications; 215, 213-223.
P. Tschelisnig (2001); Acoustic emission testing (AET) an integral non-destructive testing method; International Journal of Materials and Product Technology, 3(3/4), 267 – 275.
Rainer Pohl , A Erhard, H.J Montag , H.-M Thomas, H Wüstenberg (2004); NDT techniques for railroad wheel and gauge corner inspection; NDT & E International, 37(2), 89–94.
Rodrigo Benenson, Stephane Petti, Thierry Fraichard, Michel Parent (2008); Towards urban driverless vehicles; International Journal of Vehicle Autonomous Systems, 6(1/2), 4 – 23.
Suprenant, B. & Schuller, M. (1994); Non destructive evaluation & testing of masonry structures, The Aberdeen Group, USA.
T. Kek & J. Grum (2011); AE monitoring at laser cutting, Proceedings of the fifth conference on Emerging Technologies in NDT, Ioannina, Greece, 321-326.
Tsioulou, O., Lampropoulos, A., & Paschalis, S. (2017). Combined non-destructive testing (NDT) method for the evaluation of the mechanical characteristics of ultra high performance fibre reinforced concrete (UHPFRC). Construction and Building Materials, 131, 66-77. https://doi.org/10.1016/j.conbuildmat.2016.11.068
Umesh Singh, Mohan Singh and M. K. Singh (2012); Analysis study on surface and sub surface imperfections through magnetic particle crack detection for nonlinear dynamic models of some mining components; Journal of Mechanical Engineering Research, 4(5), 185-191.
Withers, P.M. (1994); Ultrasonics for the detection of fouling. Food Technology International Europe 1994, 96–99 (Reprint 768).
Published
How to Cite
Issue
Section
Copyright (c) 2021 International research journal of engineering, IT & scientific research
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Articles published in the International Research Journal of Engineering, IT & Scientific research (IRJEIS) are available under Creative Commons Attribution Non-Commercial No Derivatives Licence (CC BY-NC-ND 4.0). Authors retain copyright in their work and grant IRJEIS right of first publication under CC BY-NC-ND 4.0. Users have the right to read, download, copy, distribute, print, search, or link to the full texts of articles in this journal, and to use them for any other lawful purpose.
Articles published in IRJEIS can be copied, communicated and shared in their published form for non-commercial purposes provided full attribution is given to the author and the journal. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
This copyright notice applies to articles published in IRJEIS volumes 6 onwards. Please read about the copyright notices for previous volumes under Journal History.
